Prevest Denpro Accusil Putty & Light Body
Hydrophilic Vinyl Polysiloxane Impression Material Putty & Light Body
Starting at: ₹660.00 (-45%)
Prevest Denpro Accusil Light Body - 2 x 50ml (70005) |
₹1150.00 |
-
+
|
In Stock | ||
Prevest Denpro Accusil Putty - 300ml Base/ Catalyst (70004) |
₹1460.00 |
-
+
|
In Stock | ||
Prevest Denpro Accusil Combo Kit (70004-1) |
₹1500.00 |
-
+
|
In Stock | ||
Prevest Denpro Accusil Light Body - 1 x 50ml (70005-1) |
₹660.00 |
Out of stock | |||
Prevest Denpro Accusil Putty - 150ml Base/ Catalyst (70003) |
₹890.00 |
Out of stock |
Benefits
Brand warranty
Secure payments
upto 7 days returnable
Long expiry
EMI
Description
Prevest Denpro Accusil Putty is a very high viscosity two pastes elastomeric impression material with excellent hydrophilic properties, dimensional accuracy, high tear strength, and resistance to permanent deformation. It l intended to be placed on preformed impression trays to reproduce the structure of patient’s teeth and gums for fabrication of crowns, bridges, occlusal and dental implant impressions.
Indications
- Used with Accusil Light Body in a dual phase impression technique
- Suitable for all impression techniques where a high viscosity material would be desired by the operator
- Impressions of dentulous and edentulous arches, implants and precise duplication of models
Composition
- Base: Vinyl-Terminated Polydimethyl Siloxane, SIH Capped Polysiloxane, Vinyl MQ Resin,
Fillers, Viscosity Modifiers,Pigments, Flavouring Agents and Inhibitors. - Catalyst: Vinyl-Terminated Polydimethyl Siloxane, Titanium Dioxide, Vinyl MQ Resin, Fillers,
Platinum Catalyst, Viscosity Modifiers.
Prevest Denpro Accusil Light Body is silicone-based impression material for use in dentistry with an automatic mixing device. It is a hydrophilic vinyl polysiloxane impression material for the production of extraordinarily smooth and highly precision impressions for models, crowns, bridges and dentures.
Indications
- Wash material for the putty-wash impression technique
- Syringe material for the simultaneous mixing technique
- Impression material for relining
- Cavity impression of facing, inlay, onlay, etc
- Impression of crown or bridge
- Impression of partial denture
- Impression of full denture
Specification
Additional information
Weight | 0.1 kg |
---|---|
Brands | |
Variable | Prevest Denpro Accusil Light Body – 2 x 50ml (70005), Prevest Denpro Accusil Putty – 300ml Base/ Catalyst (70004), Prevest Denpro Accusil Combo Kit (70004-1), Prevest Denpro Accusil Light Body – 1 x 50ml (70005-1), Prevest Denpro Accusil Putty – 150ml Base/ Catalyst (70003) |
Features
Features
Accusil Putty
- Accurate impressions
- Extremely smooth
- Hydrophilic properties
- Exceptional dimensional stability
- High elasticity – Tear resistant
- Maximum elastic recovery
Accusil Light Body
- Excellent reproduction of marginal contours
- Excellent flow properties
- Excellent wettability
- Ideal working time
- Optimal intra-oral setting time
- Good tear strength and dimensional stability
- Compatible with all putty based VPS products
Packaging
Packaging
Prevest Denpro Accusil Putty – 150ml Base/ Catalyst (70003)
- 1 x 150ml Base Paste (Pastic Jar)
- 1 x 150ml Catalyst Paste (Plastic Jar)
- 2 x Measuring Spoon
- 1 x Instruction Manual
Prevest Denpro Accusil Putty – 300ml Base/ Catalyst (70004)
- 1 x 300ml Base Paste (Pastic Jar)
- 1 x 300ml Catalyst Paste (Plastic Jar)
- 2 x Measuring Spoon
- 1 x Instruction Manual
Prevest Denpro Accusil Light Body – 1 x 50ml (70005-1)
- 1 x 50ml Base/ Catalyst Paste
- 5 x Mixing Tips (Yellow)
- 1 x Instruction Manual
Prevest Denpro Accusil Light Body – 2 x 50ml (70005)
- 2 x 50ml Base/ Catalyst Paste
- 10 x Mixing Tips (Yellow)
- 1 x Instruction Manual
Prevest Denpro Accusil Combo Kit (70004-1)
- 1 x 150ml Jar Base Paste Putty
- 1 x 150ml Jar Catalyst Paste Putty
- 2 x Spoon
- 1 x 50ml Base/ Catalyst Paste Light Body
- 5 x Mixing Tips
- 1 x Instruction Manual
Direction to Use
Direction to Use
- Tray Selection : Accusil Putty may be used with a suitable metal tray, a firm disposable tray, or a custom tray. For maximum accuracy use rigid trays offering good retention. Use of tray adhesive is recommended.
- Dispensing : Allow Accusil Putty material to reach room temperature prior to use. Using the scoops provided, dispense equal quantities of base and catalyst.
- Note: Close jars immediately after use. Do not interchange base and catalyst screw caps or scoops.
- Mixing : Knead by hand until a uniform color is achieved.
- Note: Latex gloves should be removed and hands washed thoroughly before mixing. To obtain optimum physical properties, the mix should be completely homogenous (streak-free), usually in about 45 seconds.
Impression Procedure Two Phase/One Step Procedure(Putty wash technique)
- If there is any debris or blood, clean field with air water spray.
- Remove excess water with suction. Do not dessicate the tooth.
- Mix Accusil Light Body, (Regular Set), backfill the impression syringe or attach an intra oral tip to
the end of the mix tip for direct intraoral syringing. - Inject syringe mix into and around toothpreparations. It is suggested to syringe
completely around the margins of the preparation, making sure to keep syringe tip within impression material. Do not blast with air. - Accusil Light Body Impression Material’s hydrophilic properties improve adaptation to the
tooth enabling better “wetting”. - While syringing wash material, the assistant should mix the putty load the tray.
- Place Accusil Putty material directly into impression tray and dimple impression. (This
technique ensures the least amount of air incorporation.) Seat tray. Retain impression in position until firmly set. (Note: The material sets faster in the mouth.) Check impression in the mouth not on the bench. Note: Latex gloves should be removed and hands washed thoroughly before checking. Be sure it is firm,resilient, and non-tacky before removal. The minimum removal time (tested according to A.D.A. Specification #19) is 5 minutes from start
of mix. - Remove impression by pulling slowly to break seal, then snap out along the long axis of the tooth. Rinse impression under cold water and blow dry. Do not store impression in direct sunlight. If the impression is to be shipped, use suitable packaging to preclude distortion.
- Technique Tip: Some residual moisture prior to syringing is acceptable.
Two Phase/Two Step Procedure
- If there is any debris or blood, clean field with air water spray.
- Remove excess water with suction. Do not dessicate tooth.
- Place a polyethylene spacer sheet over putty and seat tray slowly. (Note : if a polyethylene sheet is not used, relieve the entire impression to provide at least 2 mm of space for the Accusil Light Body, (Regular Set) material.)
- Allow impression to remain undisturbed until it has set firmly (five minutes from start of mix).
- Remove impression when it reaches a rubbery consistency.
- Remove polyethylene sheet from impression surface. The impression should be washed free of saliva and thoroughly air dried before use as a base for subsequent impressions.
- Select either Accusil Light Body, (Regular Set) as a wash material and mix.
- Syringe Accusil Light Body, (Regular Set) material evenly around prepared teeth and directly onto Accusil Putty impression. Replace in mouth and allow to set for 2 minutes 30 seconds
to 3 minutes in the mouth (not including work time). - Remove impression with a direct pull.
- Store impression at room temperature. Pour impression with stone or other die materials within 14 days.
Directions for Border Molding :
- Apply Tray Adhesive to the borders of the tray.
- Dispense equal amounts of base and catalyst onto a mixing pad and knead by hand until a uniform color is obtained – mixing time: 45 seconds. Note : Latex gloves should be removed and hands washed thoroughly.
- Roll the mix into a thin rope and apply uniformly to the tray borders.
- Instruct patient to perform the various functional movements necessary for conventional border molding techniques.
- Five minutes from start of mix, remove tray and examine borders. The addition of a small mix can be used if voids or deficient areas are present. Over-extensions can be easily removed with a scalpel blade.
- The final impression can be made with Accusil Light Body,(Regular Set).
Reviews
There are no reviews yet.